2.25.2011

VCT IN THE KITCHEN? WORKS FOR ME!

After the drama surrounding the drywall, I needed a simple project. Most people would not say installing flooring is simple, but in all honesty, this was! You may remember that I had found a great deal on wood floors for the kitchen. The contractor came highly recommended, his price was right and I really wanted them. But last minute expenses ate into the budget and even though they were a good deal, we could no longer afford them. I came to this realization on a Tuesday. By Wednesday I had designed and purchased alternate flooring, and resolved to do it myself.
The only aspect of this project I wasn't comfortable doing was leveling and putting down a subfloor. The folks at the flooring store gave me good direction, Mike and I went shopping for supplies and we called Steve for the labor. We used 1/4" luan board for the subfloor. Steve installed this using gold screws every four inches at the seams, then every 6 inches across the field. After he was done, Mike spackled all the screws and seams, then gave it a light sanding.

I chose to go with VCT flooring. Is this controversial? Maybe a little too taste-specific, as my realtor might say? Perhaps. It either conjures positive memories of your grade school (as it does for me) or a fear of long hospital corridors. But I think it's all in the application. It seems to be in the middle of a resurgence for residential use, no longer relegated to 70's basements, hand-in-hand with dark wood paneling, it's okay to bring it front and center. And it comes in so many colors!

Side note: I generally hate most tile. It's too typical, especially what we could afford and with our timeframe. I went to the big box stores and tried to get myself to like something, anything in the porcelain or stone variety. It all said "blah" and "eh" to me. As I walked the aisle, I believe I mumbled these phrases out loud.

We went with Mannington Essentials in three colors; Silver White, Pewter and Night Black. I did a little internet research to define my pattern and was inspired by a basketweave I had found. Once I decided on my pattern, I hit up my digital kitchen floorplan that I had created in InDesign and started laying it out. I wanted to make sure I had the least amount of cutting to do–that the perimeter would be nice and visually even. I think this was a key step in making the process simple. That little printout of my design was critical during layout!
First step was to determine my 45 angle. I used a carpenter's square in the corner, then snapped a chalk line the length of the room. I used that line to roughly lay out the tiles to make sure they matched my computer drawing, which mine did, I couldn't believe it! I then chose a single tile as my starter and with a Sharpie I carefully outlined it. You start laying tile in the middle of the room because if you can help it, you don't want to touch the glue! I stepped on it once and lost a sock.
Next is to trowel on the glue, pay attention to manufacturer's specs. You want to do half of the room at a time, starting in the corner and working toward the middle. Oh crap, I let the extension chord sit on the glue! That was fun to remove I tell you.
Believe it or not, this glue is nontoxic with no-vocs. I was told it was safe to use while pregnant, but it is some stinky, not to mention sticky, stuff!
Wait impatiently for glue to dry from yellow to clear, which indicates it's ready for tile.
Starting with the outlined tile, carefully start placing tiles, butting them TIGHT. I referenced my printout often to make sure I didn't screw up the pattern. If you make a mistake and need to take up a tile, it's really difficult and the tile will break. Growl. This part goes fast and once complete, repeat the process on the other half of the room, then retreat to the couch with a piece of cake. I waited to do the perimeter and any cut tiles the next day, the glue gives you 24 hours to set tile.
I forgot to take a picture of my template! It was a cardboard contraption that I used to measure my cuts, and made the process fairly uncomplicated. It's okay if the tiles aren't tight to the wall since this will eventually be covered with baseboard. The tiles cut easily by scoring with a utility blade, then carefully snapping. Not gonna lie, this was simple but tedious. My fingertips were pretty raw by the end.

Once it's done, stand back and stare at it. Leave the room then comeback, just to make sure it's still there. Go ahead, let your cats crawl on it, they will be mesmerized. All that's left is to wait 24 hours for glue to set, give it a good clean using this, then coat it 3 times with this. Let it dry and you are DONE!

8 comments:

  1. Oh my word, I LOVE this!! Do you mind me asking what the cost was? Thanks!

    ReplyDelete
    Replies
    1. Thank you Katie! If I remember correctly, the tile was about $420 plus the luan board (very inexpensive) and the glue and sealant. The flooring store quoted over $2000 with installation! One thing I wish I had done professionally was the sealing and buffing. It's been two years now and I need to do this again.

      Delete
  2. My wife and I did the exact same floor! I hadn't seen anyone else do this pattern before! Crazy. Here's our blog. It's been awhile since I've updated it, but you can scroll down and see our version of the floor. We used armstrong tile.
    www.thisoldhouseotr.blogspot.com

    ReplyDelete
    Replies
    1. Your floor looks fantastic! I love it with the vintage cabinets you have. And that new kitchen sink... heavenly.

      Delete
  3. Beautiful tile floor! I want to do a VCT checkerboard floor in my kitchen, but two different floor guys were adamant that it wouldn't be any good...they said the tiles would shrink and that grime would collect between them. Have you seen this in your kitchen?
    Also, how often do you polish and buff your VCT floor? I'd rather do mine only every few years or so.

    ReplyDelete
    Replies
    1. Thank you Rebecca! I haven't noticed any shrinking of the tiles. The finish applied at the end creates a solid coating over everything, leaving no place for dirt to build between. I will say the tiles are soft and can dent easily. For instance, we rolled our refrigerator back and forth a few times once when it needed repair, and that left a dent. I don't think it's terribly noticeable. And for the price of this floor, you have to expect some sort of maintenance and care.

      So far I have only re-polished my floor once, and that was after three years. Best of luck with your floor!

      Delete
  4. i know this is an old blog, but any chance you still know the info for the sealer that you coated it with 3 times? both links come up with the "once and done" stuff!

    ReplyDelete
    Replies
    1. Hi Rachel! This is an old blog :) if interested, please check out my new site at happygohome.com! To answer your question, I believe I used Armstrong's Shine-Keeper. Home Depot must not sell it anymore, but I found it here: http://www.acehardware.com/product/index.jsp?productId=1423617&KPID=1201152&cid=CAPLA:G:Shopping_-_Floor_Care&pla=pla_1201152&k_clickid=186a81e2-3e1b-442d-a0fa-fd7c6047c28a&gclid=Cj0KCQjwgIPOBRDnARIsAHA1X3QOgGwhW79HTG6aNyazzzX2uA9gBseUyLX-nbqNZHAbiH2SmCw91moaAnIIEALw_wcB

      Delete